前和煤业东胶带运输大巷钻孔卸压围岩控制技术

为有效解决前和煤业3#煤层东胶带大巷在原有锚网索支护下围岩变形量大的问题,结合巷道变形特征,确定采用钻孔卸压技术,采用理论分析和数值模拟的方式确定卸压钻孔在修巷作业前,垂直于巷帮打设,钻孔深度为8 m,结合巷道的具体条件确定巷道采用卸压钻孔+让压支护的围岩控制方案,并采用矿压监测验证支护效果。结果表明:支护方案实施后,顶底板和两帮的最大移近量分别为141 mm和132 mm,有效解决了巷道两帮及底板鼓起量大的问题,保证了巷道围岩的稳定性。     

煤矿冲击矿压预测和防治技术浅析

结合镇城底煤矿22605工作面的地质情况和矿压情况,提出了煤炭生产中冲击矿压的预测和防治措施。通过对22605工作面的地质情况和监测数据分析处理并探究了该工作面矿压显现规律,为其设计了一套适合本工作面的冲击矿压监测和防治体系。防治体系有预防和临时解危双重防治措施,从这两方面考虑可以做到全面防治冲击矿压。该体系可以实现矿井的安全生产,保证工作人员的安全。另通过分析冲击矿压发生的基本原理和监测到的数据,建立煤矿冲击矿压防治体系,能够及时有效地将蕴含在煤体中的冲击矿压释放和消除,达到安全生产的目的。     

卫星激光通信粗跟踪系统复合控制策略

针对卫星激光通信粗跟踪系统的跟踪稳定精度指标要求高的特点,建立了基于永磁同步电机直接驱动的粗跟踪系统模型并进行了跟踪稳定误差分析。在采用传统PID控制策略存在跟踪误差较大、动态性能较差等不足的基础上,提出了一种基于粗跟踪系统的改进型前馈复合控制策略。从理论上分析了前馈复合控制策略提高了粗跟踪系统的动态性能,为降低跟踪稳定误差提供了改善方案。地面实验验证结果表明,与传统控制策略相比,改进型复合控制策略极大地降低了系统的动态跟踪误差,动态跟踪误差由606μrad降低至13μrad(1δ)。进一步的在轨实验也验证了改进型复合控制策略的合理性和先进性,总体指标满足了卫星激光通信终端的极高精度要求。本文所提出的控制策略对其他高性能跟踪伺服系统设计也具有较大的借鉴意义。     

Optimal filtering and control for wireless networked closed-loop control systems

This article studies the optimal filtering and control for wireless networked control systems (WNCSs). In WNCSs, packets may be lost in both control and feedback channels and user datagram protocol is usually used to improve the performance of the real-time control. Relevant literature indicates that the conventional optimal filtering for such a system cannot be applied in practice due to the complex calculation with Gaussian mixtures. This paper proposes a novel scheme to realize the optimal filtering and the linear quadratic Gaussian control for WNCSs, in which the controlled node performs a local estimation and the remote-control node performs the final estimation and control, and a synchronization of two estimators is guaranteed by a communication mechanism. An optimal filtering algorithm is developed, the stability condition of the filtering error covariance is obtained, optimal finite-horizon and infinite-horizon control are derived, and the stability of the closed-loop control system is proved. Numerical simulations show the validity and feasibility of the theoretical results.     

LTE系统多小区上行联合功控算法

针对传统的小区内开环功率控制算法通常以提升本小区的吞吐量性能为目标，忽略了当前小区用户对邻小区用户同频干扰的问题，为提升边缘用户性能的同时兼顾系统整体性能，提出了一种LTE系统小区间上行联合功率控制（UJPC）算法。该算法采用单基站三扇区为系统模型，以最优化系统吞吐量比例公平函数为目标，首先根据最小信干噪比（SINR）约束值和用户最大发射功率这两个约束条件得到相应的数学优化模型，然后采用连续凸近似的方法求解优化问题得出各个基站所管辖的小区内所有用户的最优发射功率。仿真结果表明，与基准的开环功控方案相比，联合功控方案在保证系统平均频谱利用率的情况下能够较大幅度地提高小区边缘频谱利用率，其最佳性能增益能达到50%。     

Distributed learning consensus control based on neural networks for heterogeneous nonlinear multiagent systems

This paper considers a novel distributed iterative learning consensus control algorithm based on neural networks for the control of heterogeneous nonlinear multiagent systems. The system's unknown nonlinear function is approximated by suitable neural networks; the approximation error is countered by a robust term in the control. Two types of control algorithms, both of which utilize distributed learning laws, are provided to achieve consensus. In the provided control algorithms, the desired reference is considered to be an unknown factor and then estimated using the associated learning laws. The consensus convergence is proven by the composite energy function method. A numerical simulation is ultimately presented to demonstrate the efficacy of the proposed control schemes.     

600MW超临界CFB机组深度调峰运行技术

经通过分析超临界CFB机组在深度调峰方面的优势,结合600MW超临界CFB机组的实际运行工况,提出机组在深度调峰前应开展的试验工作。研究600MW超临界CFB机组的深度调峰过程,从汽机、锅炉、电气等方面提出有效的技术措施,解决深度调峰可能带来的锅炉流化不良、环保参数控制困难等问题。通过在600MW超临界CFB机组上应用,机组在30%负荷深度调峰运行,工况稳定,各项参数正常,取得了较好效果。     

Development of LTCC micro-hotplate with PTC temperature sensor for gas-sensing applications

Low temperature co-fired ceramic (LTCC) micro-hotplates show wide applications in gas sensors and micro-fluidic devices. It is easily structured in three-dimensional structures. This paper presents the low power consumption micro-hotplates which were developed with PTC (positive temperature coefficient) temperature sensor and inter-digitated electrodes. The paper presents two different structures for micro-hotplate with platinum as a heating element. The PTC temperature sensor using two different materials viz. PdAg and platinum paste are developed with micro-hotplates. The simulation has been achieved through COMSOL for LTCC and alumina micro-hotplates. The temperature variation with power consumption has been measured for the developed LTCC micro-hotplates. The change in resistance of PTC temperature sensors was measured with micro-hotplate temperature. The aim of this study was to place a temperature sensor with the gas sensor module to measure and control the temperature of micro-hotplate. A SnO₂ sensing layer is coated on LTCC micro-hotplate using screen printing and characterized for the sensing of carbon monoxide gas (CO). This study will be beneficial for designing hotplates based on LTCC technology with low power consumption and better stability of temperature for gas-sensing applications.     

基于热电效应的高效环控系统

部分空间科学实验对环境温度有较高的要求，环境温度高于或低于空间科学系统能够提供的热沉温度，需要有可靠有效的加温降温处理措施。使用可靠性强的热电制冷片作为制冷制热方式和气液换热器二次换热来实现环境温度控制的需求，并对不同流体温度制冷制热效果进行分析，结果表明流体温度和目标温度差越小，热电制冷制热的效果越好。在环境温度制冷工况中，热电单元数量随电流增加先减少后增加，在制热工况中则单调递减，设计中需按照制冷工况进行热电单元数量的确定。当流体温度接近制冷制热的目标温度时，会出现整个系统总效率优于热电系统效率的区间。通过对热电单元和气液换热器的组合系统的性能计算，提供一种适于热电环控系统的计算方法和部件选型思路，对空间站环控系统的设计有重要参考意义。     

关于提升装载机电子秤检定结果测量准确度的探讨

装载机电子秤广泛应用于货场、建筑工地,如何使检定结果准确可靠,本文对自动衡器检定装置标准器量值的管理方法进行了一些探讨。